请选择 进入手机版 | 继续访问电脑版

医工之家

 找回密码
 自行注册无效!!!!请将用户名(中文单位称呼)+密码告诉QQ943299174

QQ登录

只需一步,快速开始

扫一扫,访问微社区

搜索
热搜: 医学工程
查看: 2820|回复: 1

费森血透机CPHT报警说明及其处理(贵阳罗工)

[复制链接]

3

主题

3

帖子

87

积分

班长

Rank: 2

积分
87
QQ
发表于 2016-2-16 19:19:42 | 显示全部楼层 |阅读模式
费森血透机CPHT报警说明及其处理
贵阳罗工
CPHT(周期性压力保持测试=Cycle  Pressure Holding Test)

After closing V24 and V24B and opening the V26 the machine will check thecompliance of the hydraulic.
关闭V24V24B后,打开V26机器将检查水路
1.     Compliance check:
一致性检测
After the start of the CPHT the UF pumpwill do 1 stroke
开始CPHT测试之后超滤泵动作一次
à if the pressure change is < 50 mmHg the UF pumpwill do one more stroke
à如果压力变化值< 50 mmHg 超滤泵将会做更多次动作
à from the dialysate pressure change the machine cancalculate the compliance of the hydraulic, that means if there is a Diasafefilter is installed or two Diasafe filters in case ofOnline Plus etc.
à从析液压力改变机器可以计算水路一致性,如果有一个或两个Diasafe过滤器安装Diasafe过滤器的Online Plus等等
à if after the second stroke of the pump the pressurechange is still < 50 mmHg (in case of a leakage, air in the system or wrong pressure measurement
à如果超滤泵第二次动作之后,压力改变依然< 50 mmHg(假设有泄漏,系统进空气,或者压力传感器测量错误)
à CyclicPHT F01will occur

à将会出现Cyclic PHT F01错误
(1).     Too much air in the filters(Diasafe/ Onlineplus) e.g. after filter change
太多的空气在过滤器中(Diasafe/ Onlineplus)等。填充过滤器
(2).    Too much air in thesecondary air separator (e.g. ASP malfunction). Check protective earthresistance at the socket.
太多空气在二次空气分离器中(例如:ASP泵故障)。检查插座到机器的安全接地线接地线电阻
(3).    Leakage on V 24/ 24b/ 26/43/ dialysate pressure transducer/ relief valve
电磁阀V24/V24B/V26/V43泄漏,透析液安全调压阀(78阀)泄漏。
(4).   The system used includes the Diasafe option--> Yes --> Is the Diasafe test being performed --> No
--> CPU2/array 2/ DIP switch 1 must be set to ON in any case.
机器使用Diasafe选项--> Yes ->Diasafe测试被执行--> No-> CPU2/ array 2/ DIP switch 1 无论如何必须设置为 ON
(5).   ASP leaky
ASP泵泄漏
(6).   Erroroccurs occasionally in relation to the flow without any reason. (Solution: useSW 4.50H/S)
      错误偶尔出现与流没有任何关系(解决方案:使用软件版本4.50H/S)
It's similar to the UFK calculation of the dialyser and automaticsetting of the TMP limits
类似于UFK计算透析器和自动设置TMP界限
à at thebeginning of a treatment the machine will check the dialysate pressure (9)after every UF pump stroke:
à在每次超滤泵冲程之后,机器开始治疗时将检查透析液压力传感器(9)
à if thepressure is very low and the change is quite small --> it must be a highflux dialyser (big UFK) and the alarm limits are set very small
如果压力很低,变化很小--> 它必须是一个高通量透析器(大超滤细数)和设置报警范围很小
à if thepressure is higher and the change per stroke is bigger --> it must be a lowflux dialyser (small UFK) and the alarm limits are set bigger.
如果压力很高变化很大--> 它必须是一个低通量透析器(小超滤细数)和设置报警范围很大

2.     After thecompliance check the machine will calculate the expected balancing error:
合规检查后机器将计算预期的平衡错误:
The pressure value measured bytransducer 9 should be quite stable
9号压力传感器检测得的压力值应该是相当稳定的
à if thepressure is not stable (in case of a leakage)
如果压力不稳定(万一发生泄漏)的情况下
à CyclicPHT F02will occur (calculated balancing error > ± 125 ml/h)
将会出现Cyclic PHTF02错误报警(平衡计算错误> ± 125 ml/h
(注:可设置LP632-1-5 on,机器在模拟透析下,每2分钟测试一次CPHT,并且显示当前balancing error XX ml/h,可更直观的判断。)

3.    While the machine will start to calculate thebalancing error the CPU 2 changes the setting of the measuring range (operatingpoint) on CPU 2.
而机器将开始计算平衡错误CPU 2改变测量范围的设置(操作点) CPU2中。
The resolution of the dialysate pressure measurementmust be higher during CPHT
透析液压力测量CPHT的频率期间必须更高
à thecalculation must be done with a higher resolution
计算必须用更高的分辨率
à if thefluctuation of the pressure is too high
如果压力太高的波动
à CyclicPHT F03 will occur
将会出现Cyclic PHT F03错误
·DAC converter (IC11) on P.C.B. LP632 defective
DAC转换器(IC11)P.C.B. LP632缺陷
· Operational amplifier (IC1/IC3) on P.C.B. LP632 defective
运算放大器(IC1 / IC3)P.C.B. LP632缺陷
· Acknowledgement (P_DIAL, X633L/ B6) -> X632/A29 defective
确认(P_DIAL X633L / B6)- > X632 / A29缺陷

4.     The cyclic pressureholding test could not be completed or performed even after a maximum testdelay of 180s.
周期性压力保持测试无法完成或保持测试执行超过180秒钟的最大测试延迟。
à CyclicPHT F04will occur
Cyclic PHTF04将会出现
·Fill program in progress (check protective conductorresistance at receptacle)
填充程序正在执行(检查废液腔中的阻抗探测器6是否正确)
· Blood alarm
血报警
· V43 open (e.g. TMP alarm)
        V43打开(如:TPM报警)
· Air separation pump active
空气分离泵开始激活动作
· Flow alarm
流量报警
· Flow fluctuations >±180ml/min
流量波动>±180ml/min

Below you can see thearea (marked with red arrows) which is checked during CPHT:

下面你将看到该地区(标有红色箭头)CPHT期间检查

CPHT期间检查

CPHT期间检查


无私技术共享是职业道德理念最基本的灵魂
回复

使用道具 举报

12

主题

49

帖子

4257

积分

版主

Rank: 7Rank: 7Rank: 7

积分
4257
QQ
发表于 2016-2-24 16:27:45 | 显示全部楼层
罗总不错 可以
全国临床医学工程技术职称考试交流群。群号:321366917。加群请注明某省姓氏+某级别。如:上海冯工-中级。
回复 支持 反对

使用道具 举报

本版积分规则

QQ|小黑屋|手机版|Archiver|医工之家 ( 鲁ICP备14003024号-1 )

GMT+8, 2024-3-29 19:21 , Processed in 0.162568 second(s), 32 queries .

Powered by Discuz! X3.4

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表