|
|
2.1Errorcode02SafetySoftware
The service codes 02.00.. to 02.22.. are recognised on the CPU 68332 PCB; they file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB3F.tmp.pngcorrespond to 02.40.. to 02.62.. as recognised on the Pneumatic Controller PCB.
Fault | | | | si0_Err, New start, cause incorrect, reset | Monitoring of cold/warm start storage in RAM on CPU 68332 PCB. Cause: Software error on CPU 68332 PCB | | si0_Err, Fast data chksum error, reset | Data packets between CPU 68332 PCB and Pneumatic Controller PCB cannot be transferred in full. CPU 68332 PCB or Pneumatic Controller PCB defective. | | si0_Err, Safety software of partner CPU not started, reset | After starting, it was not possible within 10 seconds to establish synchronisation between CPU 68332 PCB and Pneumatic Controller PCB. Cause: CPU 68332 PCB or Pneumatic Controller PCB defective. | | si0_Err, Input data, chksum error, reset | Data packets between CPU 68332 PCB and Pneumatic Controller PCB cannot be transferred in full. CPU 68332 PCB or Pneumatic Controller PCB defective. | | si0_Err, Vector for NMI incorrect, reset | RAM or SW error on CPU 68332 PCB | | si0_Err, Si boot, case incorrect, reset | RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. |
5664.500/800 Evita 4/Evita 2 dura 01.2002 Repair Instructions – 4
file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB4F.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB50.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB51.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB52.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB53.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB54.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB55.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB56.tmp.jpg
Fault | | | | si1_ Err, Adjuster has incorrect pixel sum, X alarm, reset: | Screen content (with Evita 2 dura also 7- segment displays) is read out and compared to request. Cause: Hardware or SW error on Graphics Controller PCB (Evita 4)/Front Panel PCB (Evita 2 dura) or CPU 68332 PCB or Pneumatic Controller PCB. If display plausible, then SW error; otherwise high probability of hardware error on Graphics Controller PCB (Evita 4) or Front Panel PCB (Evita 2 dura). Table for X:
1 Paw high adjuster selected 2 Paw high arrow selected 3 MV min adjuster selected 4 MV min arrow selected 5 O2 adjuster selected 6 Last adjuster plus one 7 Paw high adjuster not selected 8 Paw high arrow not selected 9 MV min adjuster not selected 10 MV min arrow not selected 11 O2 adjuster not selected 12 Paw high line 30 top 13 Pressure scale values top 30 14 Paw high line 60 top 15 Pressure scale values top 60 16 Paw high line 100 top 17 Pressure scale values top 100 18 Paw high line 30 bottom 19 Pressure scale values bottom 30 20 Paw high line 60 bottom 21 Pressure scale values bottom 60 22 Paw high line 100 bottom 23 Pressure scale values bottom 100 24 Paw high line 30 bargraph 25 Pressure scale values bargraph 30 26 Paw high line 60 bargraph 27 Pressure scale values bargraph 60 28 Paw high line 100 bargraph 29 Pressure scale values bargraph 100 30 Paw high display 1 31 Paw high display 2 32 MV min display 1 33 MV min display 2 34 Cold start screen |
file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB67.tmp.png5664.500/800 Evita 4/Evita 2 dura 01.2002 Repair Instructions – 5
file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB68.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB69.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB6A.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB6B.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB7B.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB7C.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB7D.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB7E.tmp.jpg
Fault | | | | si1_Err, Paw high, Si copy, consistency X alarm, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, MV min, Si copy, consistency X alarm, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, O2 adjust, Si copy, consistency X alarm, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, Paw high, invalid value, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, MV min, invalid value, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, O2 adjustment, invalid value, reset | Alarm values relevant to safety are checked for plausibility. Cause: RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, Si boot, case incorrect, reset | RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si1_Err, Xxx is set, case incorrect, reset | Only applies up to SW 1.04. RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB | | si1_Err, Control console, status, case incorrect, reset | RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. |
file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB7F.tmp.png5664.500/800 Evita 4/Evita 2 dura 01.2002 Repair Instructions – 6
file:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB80.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB91.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB92.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB93.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB94.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB95.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB96.tmp.pngfile:///C:\Users\mqs\AppData\Local\Temp\ksohtml\wpsEB97.tmp.jpg
Fault | | | | si2_Err, Identifier has incorrect pixel sum, X alarm, reset 专业德尔格呼吸麻醉机维修 13414141187姜 | Screen content (with Evita 2 dura also 7- segment displays) is read out and compared to request. Cause: Hardware or SW error on Graphics Controller PCB (Evita 4) / Front Panel PCB (Evita 2 dura) or CPU 68332 PCB or Pneumatic Controller PCB. If display plausible, then SW error; otherwise high probability of hardware error on Graphics Controller PCB (Evita 4) or Front Panel PCB (Evita 2 dura). Refer to error 02.01.001 for X table. | | si2_Err, Identifier not announced, X alarm, reset | Refer to error 02.02.001. | | si2_Err, Value has incorrect pixel sum, X alarm, reset | Refer to error 02.02.001. | | si2_Err, Si boot, case incorrect, reset | RAM or SW error on CPU 68332 PCB or Pneumatic Controller PCB. | | si3_Err, Keypad input sequence, counter incorrect, reset | SW or transmission error from Graphics Controller PCB (Evita 4) or Front Panel PCB (Evita 2 dura) via CPU 68332 PCB to Pneumatic Controller PCB. Cause: Probably error on Graphics Controller PCB (Evita 4) or Front Panel PCB (Evita 2 dura). | | si3_Err, Rotary knob button pressed, incorrectly displayed, reset | SW or hardware error when reading out keys on Graphics Controller PCB (Evita 4) or Front Panel PCB (Evita 2 dura). | | si3_Err, Silence button pressed, incorrectly displayed, reset | Refer to error 02.03.002. | | si3_Err, Reset button pressed, incorrectly displayed, reset | Refer to error 02.03.002. | | si3_Err, Extraction button pressed, incorrectly displayed, reset | Refer to error 02.03.002. | | si3_Err, Inspiration hold button pressed, incorrectly displayed, reset | Refer to error 02.03.002. | | si3_Err, Expiration hold button pressed, incorrectly displayed, reset | Refer to error 02.03.002. |
专业德尔格呼吸麻醉机维修、技术支持、配件供应！ 13414141187姜
德尔格Evita4呼吸机故障代码.doc |
|
发表于 2016-4-30 15:38:58
